Tips for High-Speed PCB Design: Designing a PCB with high-speed signals presents unique challenges that require careful planning and routing. To help PCB designers achieve optimal performance, we have compiled a list of best practices for high-speed PCB design and signal routing.Designing a PCB is a challenging task, which becomes even more complex when high-speed signals are involved. To assist PCB designers, we have compiled a list of best practices for routing high-speed PCBs to help achieve an optimal design.
1. Routing High-Speed Signals Over a Continuous Ground Plane
One of the most important tips for high-speed PCB design is to maintain a continuous ground plane beneath signal traces. Ideally, the PCB should be a four-layer board with one layer dedicated entirely to the ground plane. This approach minimizes impedance between different grounding points on the PCB and reduces the potential for noise.
2. Avoid Cumulative Placement of Vias
Improperly placed vias can create areas with increased current density. The best method is to position vias in a grid pattern, ensuring enough space for power planes to pass through.
3. Use 135° Bends Instead of 90°
In high-speed PCB design, trace bends should be kept to a minimum. If bends are necessary, it is recommended to use 135° bends instead of 90° bends to reduce signal discontinuities and maintain signal integrity.
(Using 135° bends instead of 90° bends)
4. Increase Trace Spacing to Minimize Crosstalk
A minimum spacing of four times the trace width should be maintained between adjacent copper traces in the same net. Each bend segment should be 1.5 times the trace width. Most PCB design software of does not automatically check these minimum spacing requirements.
(Increase spacing between signal traces outside of narrow areas)
Traces should have sufficient spacing to minimize crosstalk. The level of crosstalk depends on the length and spacing between two traces. In some areas, routing paths may create bottlenecks where traces are closer than desired. In such situations, the spacing between signals should be immediately increased outside the bottleneck. Even when the minimum requirement is met, further increasing the spacing can be beneficial.
(Minimizing crosstalk through sufficient and increased signal trace spacing)
5. Implement Topology Instead of Long Stubs
Long stubs can act as antennas and cause EMC issues. Stubs with improper routing can also create reflections that negatively affect signal integrity.
If such traces are necessary, route signals in a closed loop, as shown in the diagram.
(Topology of traces)
6. Proper Routing of Differential Pairs
In high-speed PCB design, differential signals should be kept at a consistent distance and routed symmetrically. This spacing helps achieve the specified differential impedance. PCB designers should minimize areas where the spacing is increased due to pad clearances.differential impedance. Designers PCB should minimize the area where specified spacing is increased due to pad clearances.
(Proper routing of differential pairs)
No components or vias should be placed between differential pairs, even if the signals are routed symmetrically. Placing components and vias between differential pairs could lead to EMC issues and impedance discontinuities.
(No components or vias between differential pairs)
7. Use Symmetric Vias and Connections
To achieve optimal performance in high-speed PCB design, trace width should match component size. The ideal trace width depends on the required impedance, and careful adjustments must be made to reduce impedance tuning issues between the signal path and components.
(Symmetric placement of vias)
When routing differential pairs in high-speed PCB design, both traces should be routed on the same layer to meet impedance requirements. The same number of vias should also be included in the routing paths.
(Symmetric placement of vias2)
8. Avoid Routing Signals Over a Split Plane
Incorrect signal return paths result in noise coupling and EMI problems. Designers should always consider the return path of a signal when routing it. Power paths and low-speed signals take the shortest return current path. However, for high-speed signals, the return current should always follow the signal path.
Tips for High-Speed PCB Design
A signal should not be routed across a split plane, as the return path cannot follow the signal trace. If a plane divides the start and endpoint of a signal, the signal path should be routed around it. If the forward and return paths are separated, the area between them behaves like a loop antenna.
Solution: Decoupling Capacitors In high-speed PCB design, decoupling capacitors should be used when a signal must be routed across two different reference planes. They provide a low-impedance path that allows the return current to pass from one reference plane to another, helping to maintain signal integrity and reduce electromagnetic interference (EMI).
Designers should avoid routing high-speed signals near the edges of reference planes or PCB boundaries, as this can negatively impact trace impedance.
9. Separating Analog and Digital Ground
To minimize noise, analog and digital ground planes should be separated. Mixed-signal circuits require both planes to be connected at a single point, ideally near the main integrated circuit.
It is always recommended to place ferrite beads or zero-ohm resistors between the analog and digital sections in schematics. In mixed-signal designs with split planes, digital signals should not be routed across the analog ground plane, and analog signals should not be routed across the digital ground plane.
10. Matching Trace Width to Component Sizes
To achieve optimal performance in high-speed PCB design, trace width should match component size. The ideal trace width depends on the required impedance. To reduce impedance tuning issues between the signal path and components, careful adjustments must be made.
